Go to…

Mercedes-Benz

Home / Mercedes-Benz

We Service and Repair all Mercedes-Benz cars

  • 2014 Mercedes-Benz CLA250

    Mercedes-Benz CLA250
    Mileage
    73,397
    Service Date
    3/22/2024
    Services Performed
    • performed engine health report found code p0 07028 outside temperature sensor has electrical bolt inspected outside temp sensor sensor is damaged possible from road hazard hitting the tip recommend replacing and retesting for further problems FOUND UNDER BODY COVER BROKEN RECOMMEND REPLACE
    • COURTESY CHECK – VISUAL INSPECTION ONLY
    • REMOVE AND REPLACE UNDER COVER
    • FOUND UNDER BODY COVER HAS BEEN BROKEN REPLACE OUTSIDE AIR TEMP SENSOR
    • AIR CLEANER ELEMENT – Remove & Replace
    • CABIN AIR FILTER – Remove & Replace
    • SPARK PLUGS – Remove & Replace
    • SERVICING THROTTLE BODY SERVICING FUEL INJECTORS SERVICING IN FUEL TANK PUMP SERVICING INTAKE MANIFOLD AND VALVES FROM CARBON BUILD UP
    • RESET OIL LIFE MONITOR SYSTEM (IF EQUIPPED)
    • PERFORM ENGINE OIL FLUSH WITH ADDITIVE
     
    KIM P. gave our service a 5 star review on 3/22/2024

  • 2004 Mercedes-Benz E320

    Mercedes-Benz E320
    Mileage
    175,249
    Service Date
    5/17/2023
    Services Performed
    • performed vehicle health report codes are as follows p2050 misfiring damage TWC p2056 misfiring cylinder 5 damage TWC P2043 misfiring p2088/p0155 heating of component G3 left O2 sensor before TWC heating capacity too low p2082/p0155 short circuit in signal left O2 sensor P2045 misfire cylinder 4 p2052 misfiring cylinder 4 p2047 misfire cylinder 6 exhaust smells very rich of gas AND SMOKING gas smell in engine oil indicating fuel leaking internal engine l vehicle has long crank hard to start and lots of hesitation. perform leak check on injectors found cylinder 4 leaking severely and minor leaking in cylinder 6 recommend replace all fuel injectors (possible other injectors could fail). valve covers have buildup from gas leaking inside. suggest removal and clean covers and inspect for cracks, perform engine flush x2 due to heavy sludge buildup oil has mud consistency and fuel system clean possible catalytic converter damage. customer concern for key fob not working and radio issues found radio fuse was incorrect replace and key fob worked properly ________________________________________________ customer concerned for seat issues gyration not working. performed vehicle health report for module. 9251 air cushion left seat air leak at cushion 9256 left seat air leak lumbar support 9258 air leak at cushion depth 9260 no or insufficient pressure supply 9305 fault in communication with control unit pneumatic pump for dynamic seat recommend additional time to continue electrical testing for seat concern
    • PERFORM ENGINE OIL FLUSH WITH ADDITIVE
    • REMOVED COMPONENTS TO GAIN ACCESS TO FUEL INJECTORS. REMOVED A TOTAL OF 6 FUEL INJECTORS & INSTALLED 6 NEW FUEL INJECTORS. RE INSTALLED ANY REMOVED COMPONENTS. ALLOWED VEHICLE TO RUN FOR A FEW HOURS TO BURN OFF AS MUCH FUEL AS POSSIBLE THAT WAS DUMPED BY OLD INJECTORS _____________________________________________
     
    PIUS A. gave our service a 5 star review on 5/17/2023

  • 2008 Mercedes-Benz S550

    Mercedes-Benz S550
    Mileage
    103,558
    Service Date
    8/26/2022
    Services Performed
    • Verified customer concern 1303 space b4/3 fuel tank pressure sensor open circuit p0451 0866 voltage supply of component motor electronic battery voltage too long p0562 1106 the voltage a really circuit 87 is too low p2505 60021 or more of the signals transmitted by the control unit engine control module or n73 eis easys control unit 6000 the supply voltage of control unit is too low under voltage 5600 power supply terminal 30 under voltage 5160 check mechanical component for proper operation and installation 5020 power supply terminal 30 under voltage 90 10 the supply voltage of the control unit is too low under voltage 9005 93b0 no can message was received from control unit ezs 9374 9362 9373 93af 9011 over voltage supply 9010 underwater supply 9007 9006 C001 00 voltage supply C002 over voltage supply Visually inspected in tank fuel filter found to be cracked replace in tank fuel filter retest no more fuel leak
    • COURTESY CHECK – VISUAL INSPECTION ONLY
    • FUEL PUMP – Remove & Replace – 4Matic,Base
     
    RYANN G. gave our service a 5 star review on 8/27/2022

  • 2007 Mercedes-Benz S600

    Mercedes-Benz S600
    Mileage
    93,315
    Service Date
    4/15/2022
    Services Performed
    • P0455 Major leakage in Purge system Performed an EVAP leak, leaks from the purge valve going to the back of the charcoal canister are within manufacturer specs, after the purge valve going to the engine compartment, the purge valve has failed. Purge system leaking in the front Left Bank. This is positive crankcase ventilation vacuum hose connector that is deteriorated and leaking .. Recommended replace positive crankcase ventilation valve vacuum hose connector due to leaks Test and recheck Part
    • COURTESY CHECK – VISUAL INSPECTION ONLY
    • REMOVE AND REPLACE MULTIPLE HOSES TO GET TO EVAP LINES (WRAPS AROUND ENGINE)
    • REMOVE LEFT SIDE FRONT COMPONENTS TO REACH EVAP AIR PIPE COMPRESSED LINE
    • perform smoke test found evap code for canister check valve failing under pressure recommend replacing valve
    • EVAPORATION CONTROL CANISTER – Remove & Replace
     
    WILLIE F. gave our service a 5 star review on 4/15/2022

  • 2007 Mercedes-Benz S550

    Mercedes-Benz S550
    Mileage
    83,352
    Service Date
    1/12/2021
    Services Performed
    • Found codes -0276 continuous Camshaft adjustment incorrect Inlet. -P0025 continuous Camshaft adjustment incorrect Outlet left side. -P0015 incorrect Outlet camshaft. -P2225 left fuel level sensor short to battery p2158 vehicle speed front axle control module traction control system implausible -P0336 2 space on sensor rotor not detected or wire fault -Recommend fuel pump sending module and transfer pump unit to make the car run and then retest camshaft position incorrect after installing fuel pump module vehicle would run and after sitting would not restart found rear sam module supplying voltage to pump but unable to supply correct amperage upon removing sam module found burnt relay and sound system fuses tapping into power source recommend alternate power source for sound system fuses and the addition of capacitors so system will not pull excessive amperage through car circuits. sunroof module needs to learn shade position in order to open glass it is unable to fully close shade due to damaged tracks or obstructions in sun roof. recommend tear down and inspection
    • FUEL FILTER – Remove & Replace – 4Matic,Base Pressure Regulator/Filter – [Includes: Bleed System on Diesel Engines.]
    • FUEL PUMP – Remove & Replace – 4Matic,Base
    • LEVEL TWO TESTING TECH REQUESTED TWO ADDITIONAL HOURS TO REACH SAN MODULE BY REMOVING AFTER MARKET AMP AND SUBS THAT WERE INSTALLED TO TEST MODULE
    • recommend fuel flush and need to check injectors after starting car it n=may have sticking fliers
    • gas
     
    ANTHONY W. gave our service a 5 star review on 1/12/2021