Verified customer concern perform health report P0128 engine coolant temperature sensor below thermostat regulating temperature C brake booster vacuum sensor circuit C0800 control module power circuit B124c universal serial bus USB circuit 2 won't cleared Multiple codes Perform visual inspection cooling field to correct coolant level Engine running for 15 minutes with AC off increase the engine speed to 3000 RPMs everybody has come to engine coolant temperature sensor parameter is greater than 176 Fahrenheit thermostat working as design Definition of disconnected the b34 engine coolant temperature sensor harness connector at the sensor waited for 2 minutes for all vehicle assistance to power down test for less than 5 ohm between the low reference circuit terminal A or 2 and ground found 1.4 ohms found less than 5 homes ignition on verify with the scan tool engine coolant temperature sensor parameter is colder than 39° with in spec Visual inspect B34 connector to engine coolant temperature sensor okay at this time no corrosion Check circuit for short to power okay pass Check system for short to ground okay pass Recommend replace engine coolant temperature sensor with factory sensor retest after repair Recommend fuel injection service
COURTESY CHECK – VISUAL INSPECTION ONLY
COOLANT TEMPERATURE SENSOR – Remove & Replace
PERFORM ENGINE OIL FLUSH WITH ADDITIVE
LUBE SUSPENSION COMPONENTS
TORQUE SUBFRAME BOLTS
TIRE ROTATION
SET TIRE AIR PRESSURE TO FACTORY SPEC
TOP OFF ALL FLUIDS
FLUSH BRAKE FLUID RESERVOIR FLUSH BRAKE LINES, CALIPERS, ABS UNIT TOP OFF FLUID
SERVICING THROTTLE BODY SERVICING FUEL INJECTORS SERVICING IN FUEL TANK PUMP SERVICING INTAKE MANIFOLD AND VALVES FROM CARBON BUILD UP
TONY H. gave our service a 5 star review on 11/18/2022
Perform the health report multiple codes were present P0741 torque converter clutch system stuck off P0742 torque converter clutch system stuck on P0752 shift solenoid 1 valve performance stuck on P0776 pressure control solenoid 2 stuck off P0796 pressure control solenoid 3 stuck off P0965 pressure control solenoid 2 system performance P0969 pressure control solenoid 3 system performance P0966 transmission control overheat Valve cover gasket is leaking Rear main seal is leaking Oil pan gasket is leaking Transmission and radiator flush recommended on radiator Excessive metal shavings in oil present Recommend transmission assembly Recommend valve cover gasket Recommend oil pan gasket Recommend rear main seal Recommended radiator flush
COURTESY CHECK – VISUAL INSPECTION ONLY
TRANSAXLE ASSEMBLY – Remove & Replace – [Includes: Programming. Includes: Confirm Fluid temperature for level check.]
PERFORM TRANS LINE AND COOLER PROCEDURE
REMOVE AND REPLACE ENGINE AIR FILTER
A/C COMPRESSOR DRIVE BELT – Remove & Replace – In-Line4 – [Includes: Serpentine and V-Belt type Belt(s).]
PERFORM ENGINE OIL FLUSH WITH ADDITIVE
PERFORM COOLING SYSTEM SERVICE
SERVICING THROTTLE BODY SERVICING FUEL INJECTORS SERVICING IN FUEL TANK PUMP SERVICING INTAKE MANIFOLD AND VALVES FROM CARBON BUILD UP
FLUSH BRAKE FLUID RESERVOIR FLUSH BRAKE LINES, CALIPERS, ABS UNIT TOP OFF FLUID
REMOVE AND REPLACE PLUGS OVER LAPPING LABOR VALVE COVERS
VALVE COVER GASKET – Remove & Replace – In-Line4 – [Includes: Camshaft Covers on Over Head Cam Engines.]
ALIGNMENT
SCOTT J. gave our service a 5 star review on 6/3/2022
Pulled vehicle in and pulled codes from ecm, found multiple codes P0014 exhaust camshaft position system performance, P0300 engine misfire detected and P2135 throttle position sensor correlation. For code P0014 found engine oil low and dirty need to start with flushing engine oil system and retest. P0300 code could be caused by previous code, flush engine oil and change filter and retest. For code 2135 confirmed with scanner data that tps sensor are not reading correctly need to replace first and retest Note: vehicle has not been test driven due to being in limp mode after repairs are done need to retest systems and test drive vehicle Recommendations: Throttle body assy. Engine oil flush and filter change
COURTESY CHECK / VISUAL INSPECTION
THROTTLE BODY &/OR GASKET – Remove & Replace – 2.2L Eng – [Includes: Perform Relearn procedure.]
PERFORM ENGINE OIL FLUSH WITH ADDITIVE
THERMOSTAT – Remove & Replace – 2.2L Eng
CHARLES A. gave our service a 5 star review on 12/17/2021
Had stored codes for all wheel speed sensors, erase codes and test drive vehicle. Code has come back on for left rear wheel speed sensor, visually inspected harness found break in wire for left rear speed sensor need to replace speed sensor Recommendations: Speed sensor (left rear)
Visual inspection found no coolant mixed with oil coolant level extremely low first stop coolant pressure shaft identify leak 1 replace radiator 2 replace coolant cap 3 perform block test to confirm if head gasket is cracked can not go forward until for the place coolant leak 4 oil overfilled 5. Water pump is leaking 6. Upper and lower radiator hoses 7. Heater by pass hoses 8. Valve cover and Intake oil leak
WATER PUMP – Remove & Replace – V6
DANNY S. gave our service a 5 star review on 5/3/2021